mirror of
https://github.com/rstrouse/ESPSomfy-RTS.git
synced 2025-12-13 02:52:11 +01:00
dce0ae0c04
* Moved shade storage from NVS. NVS storage became limited because of the wired ethernet boards. This limited the number of potential shades to around 20. * Added the ability to backup the shade configuration * Added the ability to restore the shade configuration. * Increased up. down, and tilt timing value to allow for up to 54 days of transition. The previous 16bit value did not allow for very slow shades and was limited to just over a minute. * UI cleanup and additional messages. * Transceiver tuning now applies the rx bandwidth in the proper order so no reboot is required.
125 lines
3.2 KiB
C++
125 lines
3.2 KiB
C++
#include <ArduinoJson.h>
|
|
#include <ETH.h>
|
|
#ifndef configsettings_h
|
|
#define configsettings_h
|
|
|
|
#define FW_VERSION "v1.4.0"
|
|
enum DeviceStatus {
|
|
DS_OK = 0,
|
|
DS_ERROR = 1,
|
|
DS_FWUPDATE = 2
|
|
};
|
|
|
|
class BaseSettings {
|
|
public:
|
|
bool loadFile(const char* filename);
|
|
bool fromJSON(JsonObject &obj);
|
|
bool toJSON(JsonObject &obj);
|
|
bool parseIPAddress(JsonObject &obj, const char *prop, IPAddress *);
|
|
bool parseValueString(JsonObject &obj, const char *prop, char *dest, size_t size);
|
|
int parseValueInt(JsonObject &obj, const char *prop, int defVal);
|
|
double parseValueDouble(JsonObject &obj, const char *prop, double defVal);
|
|
bool saveFile(const char* filename);
|
|
bool save();
|
|
bool load();
|
|
};
|
|
class NTPSettings: BaseSettings {
|
|
public:
|
|
char ntpServer[64] = "pool.ntp.org";
|
|
char posixZone[64] = "";
|
|
bool fromJSON(JsonObject &obj);
|
|
bool toJSON(JsonObject &obj);
|
|
bool apply();
|
|
bool begin();
|
|
bool save();
|
|
bool load();
|
|
void print();
|
|
};
|
|
class WifiSettings: BaseSettings {
|
|
public:
|
|
WifiSettings();
|
|
// char hostname[32] = "ESPSomfyRTS";
|
|
char ssid[64] = "";
|
|
char passphrase[32] = "";
|
|
//bool ssdpBroadcast = true;
|
|
bool begin();
|
|
bool fromJSON(JsonObject &obj);
|
|
bool toJSON(JsonObject &obj);
|
|
String mapEncryptionType(int type);
|
|
bool ssidExists(const char *ssid);
|
|
void printNetworks();
|
|
bool save();
|
|
bool load();
|
|
void print();
|
|
};
|
|
class EthernetSettings: BaseSettings {
|
|
public:
|
|
EthernetSettings();
|
|
uint8_t boardType = 0; // These board types are enumerated in the ui and used to set the chip settings.
|
|
bool dhcp = true;
|
|
IPAddress ip;
|
|
IPAddress subnet = IPAddress(255,255,255,0);
|
|
IPAddress gateway;
|
|
IPAddress dns1;
|
|
IPAddress dns2;
|
|
eth_phy_type_t phyType = ETH_PHY_LAN8720;
|
|
eth_clock_mode_t CLKMode = ETH_CLOCK_GPIO0_IN;
|
|
int8_t phyAddress = ETH_PHY_ADDR;
|
|
int8_t PWRPin = ETH_PHY_POWER;
|
|
int8_t MDCPin = ETH_PHY_MDC;
|
|
int8_t MDIOPin = ETH_PHY_MDIO;
|
|
|
|
bool begin();
|
|
bool fromJSON(JsonObject &obj);
|
|
bool toJSON(JsonObject &obj);
|
|
bool load();
|
|
bool save();
|
|
void print();
|
|
|
|
};
|
|
class MQTTSettings: BaseSettings {
|
|
public:
|
|
bool enabled = false;
|
|
char hostname[32] = "";
|
|
char protocol[10] = "mqtt://";
|
|
uint16_t port = 1883;
|
|
char username[32] = "";
|
|
char password[32] = "";
|
|
char rootTopic[64] = "";
|
|
bool begin();
|
|
bool save();
|
|
bool load();
|
|
bool toJSON(JsonObject &obj);
|
|
bool fromJSON(JsonObject &obj);
|
|
};
|
|
enum class conn_types : byte {
|
|
unset = 0x00,
|
|
wifi = 0x01,
|
|
ethernet = 0x02,
|
|
ethernetpref = 0x03
|
|
};
|
|
|
|
class ConfigSettings: BaseSettings {
|
|
public:
|
|
char serverId[10] = "";
|
|
char hostname[32] = "ESPSomfyRTS";
|
|
conn_types connType = conn_types::unset;
|
|
const char* fwVersion = FW_VERSION;
|
|
bool ssdpBroadcast = true;
|
|
uint8_t status;
|
|
WifiSettings WIFI;
|
|
EthernetSettings Ethernet;
|
|
NTPSettings NTP;
|
|
MQTTSettings MQTT;
|
|
bool fromJSON(JsonObject &obj);
|
|
bool toJSON(JsonObject &obj);
|
|
bool begin();
|
|
bool save();
|
|
bool load();
|
|
void print();
|
|
void emitSockets();
|
|
void emitSockets(uint8_t num);
|
|
bool toJSON(DynamicJsonDocument &doc);
|
|
};
|
|
|
|
#endif
|