mirror of
https://github.com/rstrouse/ESPSomfy-RTS.git
synced 2026-10-31 22:02:17 +01:00
cbeb56d336
- The pre-v3 build is for chips before v2.0, not v3.0: the esp32p4_es libraries stop at v1.99. The CI label and comments say so, and that no build runs on v2.x or v3.00. - A save refuses a clock mode the chip can't use: ProtoSettings takes CLKMode 0-ETH_CLOCK_ID_MAX, 0 only on the P4. Before, 1-3 saved and then stopped Ethernet at the next start. A range of one value reads "must be 0". - Tests for the pin limit (54 taken, 55 refused) and the clock limits. - The web UI's P4 pins leave out strapping pin 36 too. - The preset says ESP32-P4-WIFI6-POE-ETH, the board's name. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
58 lines
2 KiB
C++
58 lines
2 KiB
C++
#include <unity.h>
|
|
// As on the ESP32-P4, which has the RMII MAC too but takes the IDF's clock
|
|
// enum.
|
|
#define CONFIG_ETH_USE_ESP32_EMAC 1
|
|
#define CONFIG_IDF_TARGET_ESP32P4 1
|
|
#include "EthPhy.h"
|
|
|
|
void setUp() {}
|
|
void tearDown() {}
|
|
|
|
static void test_builds_with_ethernet() {
|
|
TEST_ASSERT_EQUAL(1, HAS_ETHERNET);
|
|
}
|
|
static void test_ip101_is_the_tlk110_id() {
|
|
// Waveshare's ESP32-P4-ETH boards have an IP101, which Arduino drives as
|
|
// the TLK110; the web UI's preset stores 1.
|
|
eth_phy_type_t type = ETH_PHY_MAX;
|
|
TEST_ASSERT_TRUE(ethPhyType(1, type));
|
|
TEST_ASSERT_EQUAL(ETH_PHY_TLK110, type);
|
|
}
|
|
static void test_clock_in_is_ext_in() {
|
|
// A cast would give the IDF's deprecated EMAC_CLK_DEFAULT.
|
|
eth_clock_mode_t mode = EMAC_CLK_DEFAULT;
|
|
TEST_ASSERT_TRUE(ethClockMode(static_cast<uint8_t>(eth_clock_id_t::GPIO0_IN), mode));
|
|
TEST_ASSERT_EQUAL(EMAC_CLK_EXT_IN, mode);
|
|
}
|
|
static void test_rejects_clock_out() {
|
|
// ETH.begin() keeps the clock on GPIO 50, which only takes a clock in.
|
|
eth_clock_mode_t mode;
|
|
TEST_ASSERT_FALSE(ethClockMode(1, mode));
|
|
TEST_ASSERT_FALSE(ethClockMode(2, mode));
|
|
TEST_ASSERT_FALSE(ethClockMode(3, mode));
|
|
TEST_ASSERT_FALSE(ethClockMode(4, mode));
|
|
}
|
|
static void test_a_save_takes_clock_in_only() {
|
|
// ProtoSettings refuses a CLKMode over this, so a save can't store a mode
|
|
// that stops Ethernet at the next start.
|
|
eth_clock_mode_t mode;
|
|
TEST_ASSERT_EQUAL_UINT8(0, ETH_CLOCK_ID_MAX);
|
|
TEST_ASSERT_TRUE(ethClockMode(ETH_CLOCK_ID_MAX, mode));
|
|
TEST_ASSERT_FALSE(ethClockMode(ETH_CLOCK_ID_MAX + 1, mode));
|
|
}
|
|
static void test_clock_pin_is_50() {
|
|
TEST_ASSERT_EQUAL_INT8(50, ethClockPin(0));
|
|
TEST_ASSERT_EQUAL_INT8(-1, ethClockPin(1));
|
|
TEST_ASSERT_EQUAL_INT8(-1, ethClockPin(3));
|
|
}
|
|
|
|
int main(int, char **) {
|
|
UNITY_BEGIN();
|
|
RUN_TEST(test_builds_with_ethernet);
|
|
RUN_TEST(test_ip101_is_the_tlk110_id);
|
|
RUN_TEST(test_clock_in_is_ext_in);
|
|
RUN_TEST(test_rejects_clock_out);
|
|
RUN_TEST(test_a_save_takes_clock_in_only);
|
|
RUN_TEST(test_clock_pin_is_50);
|
|
return UNITY_END();
|
|
}
|