Only loop() is subscribed. setConnected() runs on the WiFi event task
and reached SocketEmitter::endEmit(), whose plain esp_task_wdt_reset()
logged "esp_task_wdt_reset(707): task not found" on every boot. The web
and socket handlers on async_tcp did the same.
/scanaps on async_tcp called esp_task_wdt_add(NULL) after the scan,
subscribing a task that nothing resets, so the board could panic 15 s
after a scan from the UI.
TaskWdt.h resets only a subscribed task and re-adds a task after a long
call only when it was watched before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Prepares the move to Arduino 3.x / ESP-IDF 5.5, which renumbers
eth_phy_type_t (ETH_PHY_GENERIC is now 0) and only has the RMII MAC
API on the original ESP32.
- Store the PHY chip as our own id (eth_phy_id_t, the 2.x values) and
translate it by name at ETH.begin(), so NVS, backups and the web UI
keep their numbers on either framework.
- Build Ethernet only where CONFIG_ETH_USE_ESP32_EMAC is set instead of
everywhere but the C6. C3 and S3 could never use it. A stored
Ethernet connection falls back to Wi-Fi on those chips.
- /networksettings reports hasEthernet; the UI hides the Ethernet
options without it.
- Fix the UI PHY list: 5 is the KSZ8041, add the KSZ8081 (6), drop the
DM9051, an SPI chip the MAC can't drive.
- SSDP takes its address from WiFi/ETH.localIP() instead of the
tcpip_adapter API IDF 5 removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
loop(), socket client init and /discovery each read a step's time and
restarted the timer by hand. lap() does both. Also put the request timing
comment back on timeRequest() and say why /discovery logs its steps.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
timeRequest built both 112-byte descriptions (with a String copy of the URL)
on async_tcp for every request, and logElapsed threw them away for anything
under 100ms. Check worthLogging() first.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Builds SomfyFrame.cpp in the native env, with a minimal String and
no-op ESP_LOGx in the stubs, and tests:
- a fixed 56-bit frame, byte for byte, so what goes on air is pinned
- encode/decode round trips for 56-bit, 80-bit (repeats, Favorite,
Stop, steps, Toggle), RTW and RTV frames
- rejection of bad checksums, addresses, rolling codes, keys and
80-bit parity
- repeat/synonym tracking in copy()
- parsing and naming of commands
The command-name round trip fails: names the firmware reports, such as
"Step Up" and "My+Up", parse back to the wrong command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Adds an [env:native] for host-side unit tests (pio test -e native) with
a minimal Arduino.h stub, and covers the Utils helpers: _trim,
toBoolean, SETCHARPROP, sortArray and the Timestamp conversions.
The firmware envs now extend a shared [esp32] section instead of [env]
so the native env doesn't inherit the Arduino framework, the ESP32
libraries or the build scripts.
The half-hour calcTZOffset cases fail: +05:30 comes back as 2300.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
