Only loop() is subscribed. setConnected() runs on the WiFi event task
and reached SocketEmitter::endEmit(), whose plain esp_task_wdt_reset()
logged "esp_task_wdt_reset(707): task not found" on every boot. The web
and socket handlers on async_tcp did the same.
/scanaps on async_tcp called esp_task_wdt_add(NULL) after the scan,
subscribing a task that nothing resets, so the board could panic 15 s
after a scan from the UI.
TaskWdt.h resets only a subscribed task and re-adds a task after a long
call only when it was watched before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Prepares the move to Arduino 3.x / ESP-IDF 5.5, which renumbers
eth_phy_type_t (ETH_PHY_GENERIC is now 0) and only has the RMII MAC
API on the original ESP32.
- Store the PHY chip as our own id (eth_phy_id_t, the 2.x values) and
translate it by name at ETH.begin(), so NVS, backups and the web UI
keep their numbers on either framework.
- Build Ethernet only where CONFIG_ETH_USE_ESP32_EMAC is set instead of
everywhere but the C6. C3 and S3 could never use it. A stored
Ethernet connection falls back to Wi-Fi on those chips.
- /networksettings reports hasEthernet; the UI hides the Ethernet
options without it.
- Fix the UI PHY list: 5 is the KSZ8041, add the KSZ8081 (6), drop the
DM9051, an SPI chip the MAC can't drive.
- SSDP takes its address from WiFi/ETH.localIP() instead of the
tcpip_adapter API IDF 5 removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
NTPSettings::apply() waited up to 5 s in getLocalTime() for a clock that
can't be set before the network is up, then returned before it set TZ.
Every cold boot was 5 s slower and ran without its time zone. It now
calls configTzTime(), which sets the zone and starts SNTP without
waiting, and save() goes through apply(). /setgeneral checked
ntpServer twice, so a request that changed only the zone was ignored.
A restore ignored the result of ShadeConfigFile::restore() and rebooted
either way, so a bad file failed with no word to the user. The /restore
reply now validates the file and answers 400, which the restore dialog
shows, and an incomplete upload gets a 400 instead of no reply. A
failed restore changes nothing, so loop() no longer reboots after one.
/shades.tmp, a full copy of the backup with its rolling codes, is
deleted after every restore and after /updateShadeConfig.
The 6 extra bytes in the 2026-10-18 backup: TRANS_REC_SIZE stayed 74
when noiseDetection was added to the 80-byte transceiver record, so
every backup since declares it short. It is 80 now. The size check
stays a warning so those backups still restore, and the sum moves to
expectedFileBytes() with tests. The repeater record length is checked
as a warning only, since validate() also runs on shades.cfg at boot.
Commands for an unknown shade, tilt or group now log a warning, and a
socket that never pinged says so. KNOWN_ISSUES.md is updated, including
the real cause of the ~365 ms loop stall (radio_tx busy-waits each frame
on loop()'s core).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Firmware and UI files update separately, so an old index.js can run
against firmware that no longer returns secrets. It sends "" for the
field it can't fill in, which cleared the WiFi passphrase (reboot into
AP mode) or the MQTT password.
The firmware now decides: "" keeps the stored secret, unless the same
request changes the SSID or MQTT username, then it clears it (open
network). /setNetwork compares the settings after applying them, so a
kept passphrase no longer triggers a reboot. The UI cache-buster moves
to 3.0.14d.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The settings routes returned the WiFi passphrase, MQTT password and the
login password and PIN in plain text, and the debug log printed them and
the API key. Responses now carry hasPassphrase/hasPassword/hasPin flags,
logs mask the values, and an omitted secret keeps the stored one.
The UI loads secret fields empty and treats a blank field as "keep" while
the SSID or username is unchanged. Clearing a secret without changing the
SSID or username is listed in docs/KNOWN_ISSUES.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Code moves unchanged; only files and names change.
- entryPoints/WebUiRoutes.cpp: registerWebUiRoutes(), the port 80 routes
and the UI's files, with the helpers only they use.
- entryPoints/ApiRoutes.cpp: registerApiRoutes(), the port 8081 routes.
- entryPoints/Web.cpp keeps the servers' lifecycle, auth and the handlers
both route sets call; entryPoints/WebRoutes.h is what the three share.
- entryPoints/MQTT.* -> MqttConnection.*, class MQTTClass -> MqttConnection.
- outputs/SomfyMqtt.cpp -> outputs/MqttPublisher.cpp.
- outputs/Sockets.* -> outputs/SocketEmitter.*.
The subscribe and unsubscribe lists (the latter repeated
groups/+/direction/set) become MqttCommands' MQTT_COMMAND_TOPICS, and a
native test checks the parser takes every topic in it. GLOSSARY.md gains
MqttConnection and Change fan-out.
328 native tests. Flash: esp32devdbg +3,112 bytes (the routes are a second
ArduinoJson file), esp32dev -2,336 bytes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
