GPIO12 is a strapping pin on the original ESP32: high at reset, it powers
the flash at 1.8 V. A CC1101 can hold GDO2 high at power-up, so a board
with RX on 12 bootloops after a power cut until EN is pressed. It was the
default RX pin.
- RX defaults to GPIO35 on the original ESP32. Saved settings keep their
pins.
- The log warns each time the radio starts, and the radio settings show a
warning, while TX, RX or MISO is on a pin whose level at reset can stop
the chip booting (src/BootPins.h, data-src/js/pins.js).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
For boards such as Waveshare's ESP32-P4-WIFI6-POE-ETH: WiFi through the
board's ESP32-C6 on SDIO (esp-hosted), Ethernet on the P4's RMII MAC with
an IP101. Not tested on a device: no P4 board was at hand.
- platformio.ini: env esp32p4 (esp32-p4_r3, chip v3.01+) and esp32p4es
(esp32-p4, the esp32p4_es libraries, chips before v2.0). An image runs
on one of the two only, so each has its own release files, chip models
"p4" and "p4es". Both keep the OTA slot: at level 2 they leave about
128 KB of it.
- Ethernet clock mode: stored as eth_clock_id_t in the ESP32's numbering
and translated by name, like the PHY id. The P4's eth_clock_mode_t is
the IDF's emac_rmii_clock_mode_t, whose 0 is a deprecated default; only
clock in (GPIO 50) translates there.
- P4 Ethernet defaults: the Waveshare wiring (IP101 as TLK110, address 1,
MDC 31, MDIO 52, reset 51), board type 8. The ESP32's put MDIO on an
SDIO pin.
- Settings take pins up to GPIO 54, the P4's last, instead of 48.
- Radio defaults: SPI 32/33/27, CSN 46 (the framework's Waveshare
variant), TX 2, RX 3.
- Web UI: a Waveshare ESP32-P4-ETH preset, the P4's clock mode, pin lists
up to GPIO 54 without the pins the C6 link, Ethernet, USB and UART0 use.
- CI builds and releases both, with their ELFs; bootloader at 0x2000.
- ADR 0003: amended.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- ADR 0003: the C5 gets its own consequence instead of sitting in the
ADR 0006 amendment. It names the single-slot table, the chip revision
minimum (v1.0, CONFIG_ESP32C5_REV_MIN_FULL=100) and the longer WiFi
scans with 5 GHz.
- platformio.ini: the [esp32] comment names the C5 and C6 as released
debug builds; the C5 comment no longer repeats the C6's.
- Transceiver: the C5 comment says why TX and RX are 4 and 5.
- CI: the addr_fs comment names both partition tables.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- The C3's default radio pins were GPIO 12-17, which hold its SPI flash.
They are now the framework's SPI pins (SCK 4, MISO 5, MOSI 6, CSN 7)
with TX 10 and RX 3. A board with pins saved keeps them.
- ADR 0003: the amendment links ADR 0006, says the C3 needs chip
revision v0.3 or later (CONFIG_ESP32C3_REV_MIN_3), and the Ethernet
bullet names the C3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The C5 builds like the C6: a debug build with one 3 MB app slot, so it
updates over USB. At CORE_DEBUG_LEVEL=2 its image left 3.4 KB of the
1.5 MB OTA slot, under CI's 8 KB.
- platformio.ini: env esp32c5 (esp32-c5-devkitc-1).
- Chip model "c5", so the updater and releases name its files
SomfyController.*.esp32c5.bin.
- Radio defaults: the framework's SPI pins (CSN 6, MOSI 8, MISO 9,
SCK 10), TX 4, RX 5.
- Web UI: GPIO 0-28, without 13-14 (USB) and 15-22 (flash, PSRAM).
- CI builds and releases it; its bootloader sits at 0x2000.
- ADR 0003: amended.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Step 4a of docs/SECURITY_PLAN.md. Port 80 keeps the eleven HTTP routes of
ADR 0006 and the socket at /ws; everything else moved to protocol 2.
- Port 8081 (ApiRoutes) and the socket on 8080 (SocketEmitter) are gone.
Protocol 2 owns its frame buffer and loop-task check.
- Port 80 drops every route the old web UI called: reads, edits,
settings, scans, reboot, /shades.cfg, /discovery. HttpRoutes.cpp holds
what stays.
- ModelSnapshot, SnapshotSlots and the read documents are gone. The item
snapshot types stay, as ItemSnapshot, for events, MQTT and the command
replies.
- Model edits reply only to their protocol 2 op: requestResult goes.
- The settings' toJSON writers, used only by the settings routes, go.
- The _espsomfy_rts._tcp mDNS record moves to port 80, with path=/ws.
- The memory event reports the loop-rate window it closes.
- A deleted room no longer re-publishes its retained MQTT topics.
- e2e: the heap check reads the sync's status; the sync is checked on
its own instead of against /controller.
- README gets an API and ports section.
BREAKING CHANGE: ports 8081 and 8080 and the old HTTP routes are gone.
Home Assistant needs integration 3.0.0 or newer.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
From the review of #99:
- A sync could stall when a client took a slot the moment another left:
loop() used up the new client's sync on the old one. The slots move
to ProtoSlots, a pure module with native tests, and loop() takes a
slot's wants only for the client it read (takeWants).
- Deleting a group sends its shades, whose inGroup changed. Deleting a
shade unlinks it from its groups and sends them, so a new shade given
its id doesn't join them.
- next and sync with an id get an ok reply, and a message in pieces
gets one bad request, not one per piece.
- Feeds check for loop() before they write the event buffer, and log
an event too large, as events do.
- editChanges() (ModelEditor, native tests) says what clients get after
an edit; the edit result carries the shade a group gained or lost.
order() takes a sort_list_t.
- The frame writers move to ProtoFrame. Renames: pf to proto_field_t,
the X-macro letters to TYPE/FIELD/ERR/FEED, proto_request_t to
proto_message_t, REQ_* to WANTS_*, fmt to eventJson. The event
bodies share sendItem(), the connection type name lives in
ESPNetwork, and the loop() task check in SocketEmitter.
- e2e: the heap floor check skips when the low since boot is already
under it; tests for replies to next and sync and a long message.
- SECURITY_PLAN.md splits step 1 into 1a-1d.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The /ws endpoint runs next to the old socket on port 8080. The
handshake checks the token under security, the device sends hello,
then a sync of the schema (unless the client has it), header, rooms,
shades, groups, repeaters and status, paced by the client's next.
Events go out with the old ones: shadeState or the whole shade on a
config change, groups, rooms, removals, orders, repeaters,
shadeCommand, memory, wifi, ethernet, and the frames and
frequencyScan feeds.
The table of types, fields, errors and feeds is defined once and is
sent as the schema. The writer, item writers, sync and client frame
parser are pure and natively tested.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Socket events that don't fit the static buffer are logged and not sent.
The state events are small (shadeState is about 400 bytes), but
remoteFrame lists up to 300 pulse timings and real frames already came
to 1.8-2.1 KB against the 2 KB buffer. MAX_SOCK_RESPONSE is now 4096 in
SocketEmitter.h, and a static_assert next to remoteFrame fails the build
if 300 pulses of 10 digits no longer fit. KNOWN_ISSUES.md closes the
entry with the bounds of every event.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Code moves unchanged; only files and names change.
- entryPoints/WebUiRoutes.cpp: registerWebUiRoutes(), the port 80 routes
and the UI's files, with the helpers only they use.
- entryPoints/ApiRoutes.cpp: registerApiRoutes(), the port 8081 routes.
- entryPoints/Web.cpp keeps the servers' lifecycle, auth and the handlers
both route sets call; entryPoints/WebRoutes.h is what the three share.
- entryPoints/MQTT.* -> MqttConnection.*, class MQTTClass -> MqttConnection.
- outputs/SomfyMqtt.cpp -> outputs/MqttPublisher.cpp.
- outputs/Sockets.* -> outputs/SocketEmitter.*.
The subscribe and unsubscribe lists (the latter repeated
groups/+/direction/set) become MqttCommands' MQTT_COMMAND_TOPICS, and a
native test checks the parser takes every topic in it. GLOSSARY.md gains
MqttConnection and Change fan-out.
328 native tests. Flash: esp32devdbg +3,112 bytes (the routes are a second
ArduinoJson file), esp32dev -2,336 bytes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The HTTP servers and MQTT command handling go to src/entryPoints/, the
socket emitter and the MQTT and socket output of shades, groups and rooms
to src/outputs/. GLOSSARY.md names what they become once split:
WebUiRoutes, ApiRoutes and MqttCommands in, MqttPublisher and
SocketEmitter out.
Only files and include paths change. esp32devdbg flash goes from
1,546,405 to 1,546,257 bytes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The decoding of the time between received edges into frame bits moves out
of Transceiver::handleReceive unchanged into decodePulse(), with the RTS
timings and the receive buffer type. It stays in IRAM on the ESP32 and is
now covered by native tests that feed it the edges sendFrame() produces
for 56 and 80-bit first frames and repeats, a glitch and a broken pulse.
handleReceive keeps the noise guard, the edge timing and the RX queue.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The CC1101 setup, receive decoding, radio task and frequency scan move out
of Somfy.cpp, and their types out of Somfy.h into Transceiver.h, which
Somfy.h includes. The code is unchanged apart from the bit length the
radio was set up for: bit_length becomes radioBitLength, shared with the
remotes that send without one.
The radio's fromJSON stays in Somfy.cpp for now so the JSON parsing can
move into one file: ArduinoJson costs flash in every file that uses it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
